| Click to Post a New Message!
Page | [ 2 ] |
| | |
|
AMT 626 quits when hot and will not restart
Gatoraider. So I took the cover off of the lower brake pedal assembly and found the equalizer and thumb screws. I pushed the pedal and the cables are not being pulled equally. So I went to the calipers and tightened the pad adjustment screws all the way till the pads were touching the disc. Then I went back up front and adjusted the thumb screws to be the same. Then went back to the calipers and loosened the adjustment screws back off the disc. Then when I checked at the pedal the cables were still not pulling equally. Do you think uneven pad where could cause this? Thanks.
|
|
 Add Photo
Bookmarks: |
|
| |
|
AMT 626 quits when hot and will not restart
I'm thinking that you get it as close as you can and the equalizer handles the rest. Essentially it is putting the same pressure on each cable because of the equalizer, even if it's crooked. It is a primitive system and if the brakes work at all you are ahead of the game. There are many 600, 622, and 626 AMTs around with little or no brakes. Thats why everything in the system needs to be as close to perfect as you can get it.
|
|
Add Photo
Bookmarks: |
|
| |
|
AMT 626 quits when hot and will not restart
my husband is a mechanic and we are having trouble with our gator it is doing the same thing as the previous person..we replace the coil and went to the local john deer store to get an igniton module and the part he gave me is small in size kind of looks like a key... we were told is to be replaced right on the top but we cannot find it. the part is about the size of a quarter and has a single wire tab to connect. can you help? it just quit and will not start after replacing that coil..no spark and we know about a dead battery thats not the problem
|
|
Add Photo
Bookmarks: |
|
| |
|
AMT 626 quits when hot and will not restart
If you didn't have an ignitor on your motor to start with, you probably have a newer motor with the ignitor in the coil. That would explain why it won't start now. You have a coil that needs an ignitor instead of a coil with the ignitor in it. If you can take the coil and the ignitor back and get a coil with the ignitor in it, that's the thing to do. If you can't, then the black wire coming from the coil is the wire that the ignitor connects to. Connect a wire into the middle of the black wire and put a spade connection on the other end and connect it to the ignitor. The ignitor mounts on the carb linkage plate. The plate dips down from the two bolts that hold it to the motor and the ignitor mounts in the one threaded hole that's on the flat part of the plate. It should run if you hook it up that way. There is an insulator that goes under the ignitor to shield it from engine heat, I don't if the dealer gave you one or not.
|
|
Add Photo
Bookmarks: |
|
| |
|
AMT 626 quits when hot and will not restart
we have the coil where a black wire plugs into it, and also we have an ignitor but cant find where to replace it! the local dealer ran our vin # and they are saying that motor calls for an ignitor but we cannot locate it. we took all the sheilds off and still no luck..could it be under the fly wheel?
|
|
Add Photo
Bookmarks: |
|
| |
|
AMT 626 quits when hot and will not restart
I'm gonna try one more time. If you read my last post it says that the ignitor is on top of the motor mounted on the carb linkage plate which is secured to the top of the motor with two bolts. Obviously you don't have an ignitor if you couldn't see it on top of the motor. Just because your dealer says you have an ignitor doesn't make it so. If you had an ignitor there would be a Y in the black wire coming off the coil and that wire would go to the ignitor. Check the three wires, two green one black coming out from under the flywheel and make sure there isn't a splice in the black wire, if so that's where the wire to the ignitor goes. If the black wire doesn't have a splice in it and you want to use the parts you have ( coil W40449 and ignitor M119146 ) you have to cut the insulation off the black wire somewhere out over the top of the motor, attach another black wire to it and attach the other end of that wire to the ignitor. The ignitor mounts where I said in my last post. So you have the black wire attached to both the coil and the ignitor. Don't cut the wire going to the coil, ( it goes to the ignition switch to shut the motor off ) just attach the wire going to the ignitor to it. I'm sure this will work. If you don't want to do all that you need a coil PN M126972, they have the ignitors in them. That's probably what you had in the first place.
|
|
Add Photo
Bookmarks: |
|
| |
|
Page | [ 2 ] | Thread 169646 Filter by Poster:
7 | 7 | 2 |
|
()
Picture of the Day
DennisCTB
Unanswered Questions
Active Subjects
Hot Topics
Featured Suppliers
|
Gas Generator Weather Protecti
04-06-2010, 10:13 
Reply
Digg It 
Del.icio.us 